Подключил тело к адаптеру и подключил еще кабель usb подтяжку не делал, пошел коннект. Вот лог может подскажете что исправить

Код:
EMMC CID : 45010053454D3038479006C7480B507A
EMMC CSD : D00F00320F5903FFFFFFFFFF92404010
Изготовитель eMMC: ID: 0045 , OEM ID: 0100
EMMC Date: 05/2013  Rev.0x90
EMMC NAME: SEM08G , S/N:  113723403
EMMC NAME (HEX): 53454D30384700 
EMMC ROM1 (Main User Data)   Capacity: 7456 MB
EMMC ROM2 (Boot Раздел 1) Емкость: 2048 kB
EMMC ROM3 (Boot Раздел 2) Емкость: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
  Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
 Device support partitioning feature
 Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: SEM08G_ 113723403_20161031_0659.extcsd
Searching for partition tables...
Detected GPT over MBR...
Medium UUID: 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Warning: Entries Count = 128
MMCBLK0P0 (MODEM) Range:	[0X400000,0X3FFFE00] ,Len: 3C00000
MMCBLK0P1 (SBL1) Range:	[0X4000000,0X401FE00] ,Len: 20000
MMCBLK0P2 (SBL2) Range:	[0X4020000,0X405FE00] ,Len: 40000
MMCBLK0P3 (SBL3) Range:	[0X4060000,0X40DFE00] ,Len: 80000
MMCBLK0P4 (ABOOT) Range:	[0X40E0000,0X42DFE00] ,Len: 200000
MMCBLK0P5 (RPM) Range:	[0X42E0000,0X435FE00] ,Len: 80000
MMCBLK0P6 (TZ) Range:	[0X4360000,0X43DFE00] ,Len: 80000
MMCBLK0P7 (PAD) Range:	[0X43E0000,0X505FE00] ,Len: C80000
MMCBLK0P8 (PARAM) Range:	[0X5060000,0X585FE00] ,Len: 800000
MMCBLK0P9 (EFS) Range:	[0X5860000,0X65FFE00] ,Len: DA0000
MMCBLK0P10 (MODEMST1) Range:	[0X6600000,0X68FFE00] ,Len: 300000
MMCBLK0P11 (MODEMST2) Range:	[0X6900000,0X6BFFE00] ,Len: 300000
MMCBLK0P12 (BOOT) Range:	[0X6C00000,0X75FFE00] ,Len: A00000
MMCBLK0P13 (RECOVERY) Range:	[0X7600000,0X7FFFE00] ,Len: A00000
MMCBLK0P14 (FOTA) Range:	[0X8000000,0X89FFE00] ,Len: A00000
MMCBLK0P15 (BACKUP) Range:	[0X8A00000,0X90FDE00] ,Len: 6FE000
MMCBLK0P16 (FSG) Range:	[0X90FE000,0X93FDE00] ,Len: 300000
MMCBLK0P17 (SSD) Range:	[0X93FE000,0X93FFE00] ,Len: 2000
MMCBLK0P18 (PERSIST) Range:	[0X9400000,0X9BFFE00] ,Len: 800000
MMCBLK0P19 (PERSDATA) Range:	[0X9C00000,0XA7FFE00] ,Len: C00000
MMCBLK0P20 (SYSTEM) Range:	[0XA800000,0X683FFE00] ,Len: 5DC00000
MMCBLK0P21 (CACHE) Range:	[0X68400000,0X74BFFE00] ,Len: C800000
MMCBLK0P22 (HIDDEN) Range:	[0X74C00000,0X76FFFE00] ,Len: 2400000
MMCBLK0P23 (USERDATA) Range:	[0X77000000,0X1D1FFBC00] ,Len: 15AFFBE00
Done...Presets has been updated...
Сделано.
Сейчас постоянная перезагрузка на заставке.

Добавлено через 45 минут
Да еще заметил если в программе выставлено 1,8 В то читает ЕММС полностью,2,8 в читает до Searching for partition tables..., 3,3 в вообще не читает это с подключенным кабелем USB.
Последний раз редактировалось Sergey; 31.10.2016 в 18:16. Причина: оформление листинга лога